Resin Sand Pit Molding + Lost Foam White Pattern for Producing Automotive Mold Castings — Solutions for Porosity Defects Appearing in the Upper Part

Warm Tip: If you want to know more details about our construction services, materials, or project solutions, please contact us for a free consultation.

Resin Sand Pit Molding + Lost Foam White Pattern

Note: Automotive mold castings are mostly thick and heavy, and the material is mostly ductile iron/gray iron. With pit resin sand + lost foam white pattern, porosity is highly prevalent in the upper mold box. The core characteristic: the upper mold box location is where the molten iron fills last and where gases float up and accumulate. The decomposition gas from the white pattern, the gas generated by the resin sand, and the gas entrained in the mold cavity superimpose in three ways. Porosity is mostly concentrated on the top surface of the upper mold box, at the riser root, and near the parting line. Below, the causes are sorted by gas source for on-site troubleshooting.

I. Decomposition porosity caused by the white pattern (EPS/STMMA beads) itself (the most core gas source in lost foam)

Causes

  1. The white pattern beads have high density and low expansion ratio, with high EPS content. During pouring, high-temperature decomposition produces large amounts of H₂, CO, and hydrocarbon combustible gases; the white pattern is thick and large, attached to the upper mold box position, and the gas volume is large.
  2. The white pattern is not dried thoroughly and contains internal moisture and residual foaming agent, which instantly generates gas when heated.
  3. Too much white pattern bonding glue and accumulated glue seams; the glue generates far more gas at high temperature than the foam itself, and porosity preferentially appears at the upper mold box bonding locations.
  4. The white pattern absorbs moisture again during placement and after coating application.
  5. Pattern structure: large flat plates and thick blocks in the upper mold box area; the foam decomposition gas cannot be discharged in time and is directly trapped on the upper surface of the casting.

Countermeasures

  1. Use qualified low-density white patterns; for automotive molds, STMMA copolymer material is preferred, with fewer decomposition products and lower gas generation; control bead density and do not blindly thicken the foam.
  2. Dry the white pattern thoroughly at 45–55°C, and store it sealed after drying to prevent moisture reabsorption; focus on control in rainy and high-humidity environments.
  3. Use thin glue and apply less glue for bonding; keep glue seams as narrow as possible and scrape off excess glue; for large-area splicing, hot-melt bonding is preferred to reduce glue usage.
  4. Hollow out and reduce weight in the upper mold box foam area as much as possible to reduce foam volume and lower total gas generation.

II. Problems with the lost foam refractory coating layer (permeability, cracking, water retention)

Causes

  1. The coating layer is too thick and too dense, with poor permeability; foam decomposition gas cannot pass through the coating, and the gas is enveloped by the molten iron and accumulates in the upper mold box to form porosity.
  2. The coating is not thoroughly dried, and residual moisture inside the coating vaporizes at high temperature, forming water-vapor porosity (the inner wall of this kind of porosity is bright).
  3. The coating has poor adhesion; the coating in the upper mold box position cracks and peels, resin sand grains intrude, and at the same time the gas channel is disrupted and gas is trapped.
  4. The coating aggregate selection is incorrect, and the flake graphite ratio is inappropriate; at high temperature, sintering blocks the gas-permeable channels.

Countermeasures

  1. Control coating thickness; for automotive molds it is generally 1.5–2.0 mm, applied in 2–3 coats, thin coats applied multiple times, not one thick coat.
  2. Dry the coating in stages: low-temperature pre-drying → medium-temperature thorough drying; test moisture after drying and only sand up after thorough drying; the pit environment has high humidity, so drying time must be extended.
  3. Adjust the coating formula to ensure high-temperature permeability; for the fine-shell process, appropriately relax permeability; ordinary lost foam coatings must not be made too dense.
  4. After application, inspect the top surface of the upper mold box and corner positions; repair by re-brushing where the coating has cracks or peeling.

III. Gas generation and gas evolution problems of resin sand (furan resin sand) pit molding (high incidence in the upper mold box)

Causes

  1. Resin and curing agent addition amounts are on the high side, and the resin sand itself has high gas evolution; the upper mold box sand layer is thick, and after the resin cures, it continuously releases formaldehyde, CO, and water vapor when heated.
  2. Resin sand mixing is uneven, with local resin enrichment, and gas generation at that location surges.
  3. The used sand reuse rate is too high, the loss on ignition of used sand exceeds the standard, residual resin is high, and the sand material itself has excessive gas evolution.
  4. Insufficient sand mold curing: free curing agent and unreacted resin remain in the sand mold, generating large amounts of gas during pouring; or over-curing makes the sand mold brittle, creating gaps between the coating and the sand mold that trap gas.
  5. Pit sand mold absorbs water: moisture from the bottom of the pit rises upward, the sand mold absorbs moisture, and the water vaporizes to generate gas.
  6. The upper mold box sand mold compactness is uneven; local areas are too dense with poor permeability, and gas cannot be discharged into the sand layer.

Countermeasures

  1. On the premise of meeting strength requirements, control the resin and curing agent addition ratios at the minimum; do not add too much.
  2. Stabilize mixing time to ensure uniform resin; regularly test the loss on ignition and gas evolution of used sand; if exceeding standards, reduce the used sand ratio or use thermal reclamation.
  3. Strictly control sand mold curing time; wait until the sand mold is fully cured and the reaction is complete before placing the white pattern and pouring; it is forbidden to close the mold before the sand mold is cured.
  4. Do moisture-proofing at the bottom of the pit and lay a water-barrier layer to prevent underground moisture from permeating upward into the sand mold; shorten sand mold standing time in humid weather.
  5. At the top surface of the upper mold box and gas accumulation areas, appropriately reduce compactness to improve the sand mold’s venting capacity.

IV. Venting system design defects (most prone to pitfalls in the upper mold box)

Causes

  1. Improper arrangement of vent plugs and vent channels: there is no venting at the top surface of the upper mold box, around the riser, or at the highest position of the casting; after gas floats up, there is nowhere for it to go, and it is trapped on the upper surface of the casting.
  2. Vent plugs are blocked by coating or resin sand and lose their venting function; the number of vent plugs is small and the diameter is too small.
  3. Top pouring or side pouring in the gating system; the molten iron quickly seals the mold cavity vents, and the foam decomposition gas cannot be discharged in time, causing gas entrapment.
  4. In pit molding, the upper mold box has no dedicated gas-collecting riser or vent riser, and venting relies only on the casting body.
  5. Pouring speed is too fast; the molten iron level rises rapidly and seals the mold cavity early, and gas cannot escape in time.

Countermeasures

  1. Densify vent plugs at the highest point of the upper mold box, large flat plate areas, and riser roots; set vent risers at the highest point of the upper mold box; for thick and heavy automotive molds, vent risers must be sufficiently large.
  2. Protect the vent channels when applying coating and filling sand; after completion, clear the vent plugs to prevent blockage.
  3. Prefer bottom pouring or step pouring so that the molten iron rises smoothly and does not quickly seal the mold cavity; control pouring speed to leave time for foam decomposition gas to be discharged.
  4. Add gas-collecting grooves in the upper mold box connected to vent plugs to centrally guide the floating gas out of the sand mold.

V. Porosity caused by molten iron melting, inoculation, and material (mainly hydrogen porosity)

Causes

  1. High hydrogen content in molten iron: severely rusted and damp charge materials; scrap steel and returns carrying water and oil; damp inoculants and nodularizers directly introduce hydrogen.
  2. Tapping temperature is on the low side; molten iron viscosity is high, and dissolved gas is not easy to float up and precipitate out; for thick and heavy mold castings, the molten iron solidifies slowly, and gas has time to accumulate and grow.
  3. Excessive inoculation or improper stream inoculation method introduces water vapor.

Countermeasures

  1. Sort charge materials; rusted, oil-contaminated, and damp materials are forbidden in the furnace; all alloys, inoculants, and nodularizers must be dried in advance.
  2. Control an appropriate tapping temperature to ensure molten iron fluidity and facilitate gas floating up; for thick and heavy molds, the temperature must not be too low.
  3. Perform good degassing before the furnace to avoid excessive hydrogen content in the molten iron.

VI. Mold closing, pit operation, and environmental entrainment porosity

Causes

  1. During mold closing, floating dust and debris on the sand mold and white pattern surface are not cleaned; after mold closing, the debris burns and generates gas; mold closing misalignment causes flashing and air entrapment.
  2. During pit sand filling, the impact is too large, the white pattern coating is knocked and damaged, resin sand directly contacts the foam, and gas is rapidly generated locally.
  3. During pouring, ignition is not in place; the lost foam process does not ignite and exhaust, combustible gas accumulates inside the mold cavity, pressure rises, and back pressure causes porosity.
  4. During pouring, the flame overflow port is blocked, the mold cavity pressure rises, and gas cannot be discharged.

Countermeasures

  1. Before mold closing, blow clean the floating sand and dust in the mold cavity; check that the coating is intact, mold closing positioning is accurate, and gaps are sealed.
  2. Fill pit sand in layers with light vibration to avoid impact scraping and breaking the coating; fill sand in layers and compact in layers.
  3. Follow the lost foam process specification for ignition; ignite at the gas outlet to continuously burn the decomposition gas and reduce mold cavity pressure; ensure ignition is unobstructed.
  4. Observe the flame at the gas outlet during pouring; when the flame goes out or pressure builds up, slow down the pouring speed.

VII. Auxiliary causes: parting line, chills, and inserts

  1. Chills and inserts placed in the upper mold box are not dried and have oil contamination and moisture on the surface, generating gas at high temperature; accumulated porosity is very likely to appear near the chill locations.
  2. Chills block the gas floating channel, and gas accumulates below the chills.

Countermeasures: sandblast and derust chills, dry them thoroughly, arrange chills to avoid the gas floating channel in the upper mold box, and add vent plugs around chills.

Quick troubleshooting sequence

  1. First look at the porosity morphology: bright water-vapor porosity → moisture source (coating/sand mold/white pattern moisture absorption); honeycomb-like with carbon black on the inner wall → foam decomposition gas (typical lost foam porosity); dispersed fine pinholes → hydrogen in molten iron.
  2. Step 1: Check whether the upper mold box venting system is unobstructed and whether there are enough vent risers.
  3. Step 2: Verify white pattern drying, glue usage, and coating drying status.
  4. Step 3: Check resin sand curing, pit moisture return, and resin addition amount.
  5. Step 4: Pouring speed and ignition operation.
  6. Step 5: Molten iron raw materials and melting degassing.

Leave a Reply

Your email address will not be published. Required fields are marked *