QT500-7 tensile strength qualified but yield strength unqualified — what are the causes?

Warm Tip: If you want to know more details about our construction services, materials, or project solutions, please contact us for a free consultation.

QT500-7: Tensile strength passes, yield strength low

Standard: separately cast test bar Rm ≥ 500, Rp0.2 ≥ 320, A ≥ 7%

Core mechanism: Tensile strength reflects the final fracture resistance, while yield strength reflects the matrix’s resistance to plastic deformation; too little pearlite and too high a ferrite proportion are the number one cause, followed by nodularization/graphite morphology, cooling, sampling, and testing issues.

1. Matrix structure (highest incidence)

Ideal matrix for QT500-7: pearlite 35%–45%, the rest ferrite.

Too little pearlite (<30%), large areas of coarse ferrite: tensile strength can still be pulled above 500 by graphite dispersion and matrix load-bearing, but yield strength drops significantly, the yield-to-tensile ratio is low, and elongation is on the high side (often A > 10%). This is the most common metallographic feature of this phenomenon.

Pearlite is not fine lamellar but coarse and bulky, with poor strengthening effect, so yield strength cannot rise.

Improvement measures: moderately add Cu (0.3–0.6%) and a small amount of Sn (0.008–0.015%) to stabilize pearlite; do not add excessive silicon, as silicon promotes ferrite.

2. Nodularization and graphite morphology (second most common)

Nodularization decay, local vermicular/bulk graphite: vermicular graphite makes yield strength decline more sensitively than tensile strength; tensile strength can still barely pass, but yield strength collapses first, and elongation fluctuates greatly.

Too few graphite nodules, coarse graphite: coarse graphite nodules begin to induce matrix slip at low stress, causing premature yielding; the tensile fracture threshold is still relatively high.

Low residual magnesium, high sulfur: S > 0.02 easily consumes Mg, causing local poor nodularization.

Control: residual Mg 0.03–0.045%, keep S ≤ 0.015 as much as possible; stream/in-mold secondary inoculation to increase graphite nodule count and refine graphite.

3. Cooling rate and wall thickness effect (very easily overlooked)

Test bars/castings cool too slowly, stay at high temperature for a long time, large amounts of ferrite precipitate, and pearlite decomposes; this is especially obvious in thick-walled parts: the attached test bar itself has a lower standard yield lower limit, and using the thick-walled body to benchmark against the separately cast 320 MPa directly leads to a failure judgment.

Too high pouring temperature, too strong sand mold insulation, and an overly slow cooling curve → ferritization.

Verification: with the same molten iron, thin test bars pass yield but thick test bars have low yield — this is a cooling problem.

4. Effect of chemical composition

Si on the high side (>2.9%): a strong ferritizing element that directly lowers the pearlite proportion and reduces yield strength.

Mn too low (<0.3%): Mn is a pearlite-stabilizing element; but too high Mn easily produces carbides and embrittlement.

P on the high side: phosphide eutectic generally affects elongation more, but when on the high side it also changes matrix slip behavior and increases dispersion.

5. Testing and specimen issues (rule out first to avoid futile process adjustments)

  1. Yield strength is Rp0.2 (proof strength at 0.2% plastic extension), not the old-standard yield point; incorrect extensometer and gauge length settings on the testing machine are the most likely to produce a low Rp0.2 measurement, with little effect on tensile strength.
  2. Micro shrinkage porosity, shrinkage cavities, and slag inclusions inside the specimen: defects are more sensitive to yield strength, while tensile strength can still reach 500.
  3. Body sampling vs. separately cast test bar: body properties are naturally lower than separately cast test bars; for large wall thickness, acceptance should follow the attached-cast index of GB/T1348, and 320 MPa should not be rigidly applied.

Quick troubleshooting sequence (workshop practical)

  1. First verify: whether it is the Rp0.2 measured value, whether the extensometer is normal, and whether the specimen has internal shrinkage porosity.
  2. Do metallography: check pearlite proportion, graphite nodularization rate, presence of vermicular graphite, and graphite size.
  3. Look at elongation: A clearly > 10% → high probability of excessive ferrite and insufficient pearlite (number one suspect).
  4. Chemical analysis: S, residual Mg, Si, Cu, Mn.
  5. Verify test bar wall thickness and cooling conditions.

Common corrective directions (as-cast QT500-7)

Target stable pearlite 35–45%: Cu 0.25–0.5%, trace Sn if necessary; press Si down to the 2.4–2.7 range.

Strengthen secondary inoculation, shorten the time from nodularization to pouring, and prevent nodularization decay.

Appropriately accelerate cooling; thick and heavy parts must not blindly benchmark against separately cast test bar indices.

Keep residual magnesium stable at 0.03–0.045, and strictly control S.

Leave a Reply

Your email address will not be published. Required fields are marked *