Warm Tip: If you want to know more details about our construction services, materials, or project solutions, please contact us for a free consultation.
QT450-10 pad plate — cause analysis of overall shrinkage scale
First, a clarification: free shrinkage of ductile iron is not the same as gray iron. QT450-10 has graphitization expansion. Under normal process conditions, for thick and solid pad plate-type parts, the pattern shrinkage allowance is generally 0.8%–1.0% (8–10 mm for a 1-meter part; smaller parts proportionally). Your finished product only shrank 1 mm, which intuitively means: the actual shrinkage of the casting is far less than the preset shrinkage allowance, the casting is oversized, the pattern shrinkage allowance is insufficient, or the casting has undergone expansion that offsets the shrinkage.
Premise distinction: pad plates are generally flat plate-type parts with uniform wall thickness, without drastic thickness differences, and this is not local bulging. It is overall oversized dimensions, with total shrinkage of only 1 mm.
I. Core mechanism: excessive graphitization expansion of ductile iron offsets solid-state shrinkage
During solidification of ductile iron, graphite precipitation produces volume expansion, which is the main cause:
- Carbon equivalent on the high side: High C and Si, carbon equivalent exceeding 4.6%, large graphite precipitation amount, strong expansion; under the condition of sufficient sand mold rigidity, the expansion of the thick and solid pad plate pushes the casting outward, eating up the shrinkage that should have occurred, so the finished dimensions become larger and the measured shrinkage scale is very small.
- Excessive inoculation: Too much inoculant, excessive secondary inoculation, many graphite nuclei, more graphite grows, and the expansion effect is further amplified.
- Nodularization treatment temperature on the low side, slow solidification, more complete graphite precipitation, longer expansion time.
II. Sand mold rigidity factors (key point for static pressure/clay sand molding)
For flat plate parts like pad plates, if the sand mold has high rigidity, the mold cavity is not easily expanded. However, the ductile iron’s own expansion will feed inward and push the mold cavity outward:
- High clay sand compactness and sufficient sand shooting in static pressure molding result in very small sand mold deformation. The expansion will not push the sand mold away, but the graphite expansion of the casting itself offsets shrinkage;
- Large sand box sand coverage and firm box clamp locking leave almost no yielding in the mold cavity, making it more likely that “shrinkage is offset by expansion” and dimensions are oversized.
Conversely: if the sand mold is soft and has large yielding, expansion will push the sand mold larger and the casting will also become larger, but this is generally accompanied by mold wall movement and surface bulging. Your case is overall uniform oversizing without bulging, so graphitization expansion is the priority.
III. Pouring temperature factors
Low pouring temperature:
If the ductile iron pouring temperature is low, solidification is fast, liquid shrinkage becomes smaller, the graphite expansion proportion is higher, and the overall shrinkage amount decreases.
Too high pouring temperature: large liquid shrinkage, instead more likely to cause large shrinkage scale and shrinkage cavities.
IV. Process and structure factors
- The pad plate wall thickness is on the large side, belonging to thick and heavy ductile iron parts. The graphite expansion effect of thick parts is far stronger than that of thin-walled parts; thin-walled ductile iron cools quickly, graphite cannot fully precipitate in time, expansion is weak, and the shrinkage scale is close to that of gray iron.
- Gating system: bottom pouring, smooth mold filling, uniform mold cavity temperature, synchronous solidification of the whole plate, uniform expansion, no local dimensional abnormality, manifested as overall uniform oversizing.
- Cooling speed: slow cooling (thick sand burial, late shakeout), more complete graphitization, more obvious expansion.
V. Pattern and measurement troubleshooting (first rule out non-metallurgical causes)
- The pattern shrinkage allowance itself was calculated incorrectly: for example, the pattern only allowed 0.5% shrinkage, so the theoretical reserved amount is small, and the finished product appears to have shrunk only 1 mm;
- Measurement error: insufficient time for cooling to room temperature, the casting still has temperature, and hot-state measurement gives oversized dimensions; ductile iron pad plates dissipate heat slowly, and thick plates take dozens of hours to stabilize.
- The pattern itself was machined oversized.
VI. Corresponding preventive adjustment plan (in debugging order)
- Control the carbon equivalent first: For QT450-10 pad plates, control the carbon equivalent in the 4.3%–4.5% range, appropriately reduce carbon or silicon to reduce graphite expansion; do not blindly use high carbon and high silicon.
- Reduce inoculation amount: Reduce stream inoculation and in-ladle inoculation addition amounts to avoid excessive graphite precipitation.
- Appropriately increase the pouring temperature (within the process allowance) to increase liquid shrinkage and balance the expansion effect.
- Confirm the cooling schedule: Unify the shakeout time, and must wait until the casting is completely cooled to room temperature before re-measuring dimensions.
- Shrinkage scale compensation: If this process is stable and there are no shrinkage cavity defects, it means the actual effective shrinkage scale under this set of conditions is very small. Directly modify the pattern and re-set the dimensions according to the actual production measured shrinkage scale; do not copy the textbook 1% shrinkage scale.
Supplementary risk
Excessive graphite expansion, although causing oversized dimensions, means thick pad plates are very likely to be accompanied by internal shrinkage porosity. QT450-10 pad plates should be inspected by non-destructive testing at the same time; do not only look at dimensional qualification and ignore internal shrinkage porosity.
